The time has come… Let’s show these Southern Utah Crawlers what us Northerners are made of! Join High Noon Hobby in our takeover of the one and only Sand Hollow, Utah–one of the greatest destinations on earth for rock crawling. Get your fill of red rock and sunny days with the fellow nerds, with the added twist of a little Night Comp this time!
This is an optionally multi-day event. The High Noon Crew will be hosting trail crawls on Friday (06/03/2022) and Sunday (06/05/2022). The main competition will be held at night on Saturday (06/04/2022). The High Noon Crew will be camping at the Sand Pit campground, and encourages participants to join us for the weekend to maximize the fun!
Show up and show your support for ‘Crawling for a Cause!’ 50% of all proceeds will be donated to the Utah 4 Wheel Drive Association.
WHERE: Sand Hollow State Park, UT
WHEN: June 4, 2022 08:00 PM
Participation Costs:
10 Gate-$5 for a single class entry or $10 for all class entry
Scale Expo-Free
Trail Crawls-Free
Lunch (only provided on day of competition)-Free burgers, chips, and a drink for all 10 Gate competitors, or $5 if not competing
Event Sponsors: TBA Soon!
Event Schedule:
9:00-10:00-Participant Signups
10:00-10:15-Event Orientation
10:30-10 Gate Begins! [Class One]
11:30-10 Gate [Class Two]
12:30-Lunch & Scale Truck Expo
1:30-10 Gate [Unlimited]
2:30 Event wrap-up, giveaways, prizes awarded
This event will include:
• Ten Gate Competition (Modified SORRCA Rules):
• 1st, 2nd, and 3rd place in each class will receive prizes from our event sponsors!
• Class 1-
• Vehicle must have a windshield that fills the entire windshield frame.
• Full width bumpers are required on the front and rear of the vehicle. Bumpers that are molded into the body qualify. A rear bumper is not required on a flatbed, but adding one to the flatbed will gain the additional scale points. (Bumpers are measured from the outsides and must be the width of your windshield).
• Wheels must be aligned within the body wheel wells (center of wheels to center of wheel wells +/- 1/2 inch total combined)
• The vehicles body must be mostly intact. Only mild trimming such as flairs & removing a hardtop are allowed. If the hardtop is removed, a full interior is required (no extreme trimming of bodies allowed.
• The tread of the tires cannot extend outside of the wheel wells more then 1/2 of the tread width, flairs can be added to reach min. spec.
• Vehicle must run a full length rail chassis (The rail chassis must be as long as the vehicles wheelbase)(Tamiya CC-01 chassis are allowed).
• Truggies are not allowed, flatbeds with full length rail chassis are allowed. The bed must be as wide as the cab the entire length of the bed. Cab only not allowed.
• Tires can never extend beyond the body’s bumpers or the rear of any truck bed. (Any stingers, fairleads, shackles, bolts, etc are not considered part of a bumper when determining this.)
• Dovetailing is not allowed.
• Sectioning or narrowing of the body is not allowed.
• Bobbing a truck bed is allowed, but must follow all body specs.
• Boat sides are not allowed.
• 106mm / 4.19″ Max tire size including spares.
• Gates will be a minimum of 11″ wide (so mind your width).
• NO DIG or 4WS allowed
• Class 2-
• A front bumper is required and must be mounted to the vehicle’s chassis (chassis cross rails DO count as bumper).
• Truggies are allowed, but it must be a structural part of the rear of the vehicle.
• Flatbeds are allowed. The bed must be as wide as the cab up to the rear axle.
• 2 of the 3 following modifications are allowed: – Dovetailing the rear (1/2 the width of the widest part of the cab) a truggy/tube bed that is narrower than the cab counts as a dovetail. – Boat sides (no more than 1.25″ measured vertically from the bottom of the skid). – Pinching the front (2/3 the width of the widest part of the cab).
• 120mm / 4.75″ max tire size with a 2.2 max rim size including spare.
• Gates will be a minimum of 12″ wide (so mind your width).
• NO DIG or 4WS allowed
• Class 3 (Unlimited)-
• 146mm / 5.75″ max tire size with a 2.2 max rim size (including spare).
• A bumper is not required, but to be counted for points it must be mounted to the vehicle’s chassis and wider than the the chassis rails (chassis cross rails do not count as bumpers).
• Gates will be a minimum of 13″ wide.
• Body modifications including, but not limited to, pinched front, dove-tailing and boat-siding are permitted.
• DIG and 4WS is allowed.
• Scale Truck Expo-
• Enter your truck in the Scale Truck Expo for your chance at winning some fantastic prizes, courtesy of our event sponsor!
• A panel of judges will be randomly selected from event participants and will independently judge all of the trucks.
• There are no specific rules for your truck; may the most rad build win!
• 1st, 2nd, and 3rd place winners receive prizes.
• Truck judging will take place during lunchtime.
We look forward to seeing you out on the course! Remember to bring water and good shoes, and we also recommend a good hat to keep the sun off your face. Water jugs will be provided to refill water bottles. There are no private facilities at this event, so keep that in mind!
All are welcome! You do not need to compete in Ten Gate to be a part of this event. There is plenty of rock to share if you aren’t into spectating!
This is an overnight optional event! If you plan to spend the night with us, please note that High Noon Hobby does not provide camping supplies or meals prior to the event.
